求助 vir小鸡套用ipv6的问题

昨晚上梦见你了

在tunnelbroker上申请了ipv6，直接执行也可以了，但是  加入到开机启动怎么也不成功，
于是手动启动一下sh脚本 ，出错了

root@BlueSnarling-VM:~# bash /mycmd/ipv6.sh
: Unknown host
ifconfig: `--help' gives usage information.
: Resolver Error 0 (no error)
: Unknown host
ifconfig: `--help' gives usage information.
SIOGIFINDEX: No such device
SIOGIFINDEX: No such device


但是我一行一行的从tunnelbroker复制过来就没有问题，可以完美的打开ipv6，

请教   开机自启动的方法！

uuh

      沙发。 VIR支持IP6吗      




  ∮⊱⊱⊱     遇到懂我的人是幸运，遇不到也是正常了，沉默，喜欢独处，三观正，比你想象的深情，也比你以为的冷漠。   ⊰⊰⊰∮

              

  尾巴不止能用来挠痒痒
   还能凑字数

昨晚上梦见你了

uuh 发表于 2021-3-16 15:10
沙发。 VIR支持IP6吗      

用tunnelbroker套的，所以每次开机都要执行以下命令  很麻烦，用脚本总是失败

ymcoming

vir支持IPV6的：

[IPV4测试]
您的出口IP不能解锁Netflix，仅支持自制剧的观看

[IPV6测试]
您的出口IP完整解锁Netflix，支持非自制剧的观看
原生IP地域解锁信息：美国区(US) NetFlix 原生IP

uuh

     手输脚本可以执行。命令没问题。就多百度类似教程套用一下。




  ∮⊱⊱⊱     即使如此，我也有我想保护的世界！——《高达seed》   ⊰⊰⊰∮

              

  尾巴不止能用来挠痒痒
   还能凑字数

昨晚上梦见你了

ymcoming 发表于 2021-3-16 15:20
vir支持IPV6的：

我的不支持哎，怎么弄，教教呗

Num0

我的vir吃灰机没有ipv6

llyang

修改  /etc/sysctl.conf
net.ipv6.conf.all.disable_ipv6 = 0
net.ipv6.conf.default.disable_ipv6 = 0
net.ipv6.conf.lo.disable_ipv6 = 0
sysctl -p
sysctl.conf 修改生效, 启用IPv6

昨晚上梦见你了

llyang 发表于 2021-3-16 15:31
修改  /etc/sysctl.conf
net.ipv6.conf.all.disable_ipv6 = 0
net.ipv6.conf.default.disable_ipv6 = 0

#
# /etc/sysctl.conf - Configuration file for setting system variables
# See /etc/sysctl.d/ for additional system variables.
# See sysctl.conf (5) for information.
#

#kernel.domainname = example.com

# Uncomment the following to stop low-level messages on console
#kernel.printk = 3 4 1 3

##############################################################3
# Functions previously found in netbase
#

# Uncomment the next two lines to enable Spoof protection (reverse-path filter)
# Turn on Source Address Verification in all interfaces to
# prevent some spoofing attacks
#net.ipv4.conf.default.rp_filter=1
#net.ipv4.conf.all.rp_filter=1

# Uncomment the next line to enable TCP/IP SYN cookies
# See http://lwn.net/Articles/277146/
# Note: This may impact IPv6 TCP sessions too
#net.ipv4.tcp_syncookies=1

# Uncomment the next line to enable packet forwarding for IPv4
#net.ipv4.ip_forward=1

# Uncomment the next line to enable packet forwarding for IPv6
#  Enabling this option disables Stateless Address Autoconfiguration
#  based on Router Advertisements for this host
#net.ipv6.conf.all.forwarding=0


###################################################################
# Additional settings - these settings can improve the network
# security of the host and prevent against some network attacks
# including spoofing attacks and man in the middle attacks through
# redirection. Some network environments, however, require that these
# settings are disabled so review and enable them as needed.
#
# Do not accept ICMP redirects (prevent MITM attacks)
#net.ipv4.conf.all.accept_redirects = 0
#net.ipv6.conf.all.accept_redirects = 0
# _or_
# Accept ICMP redirects only for gateways listed in our default
# gateway list (enabled by default)
# net.ipv4.conf.all.secure_redirects = 1
#
# Do not send ICMP redirects (we are not a router)
#net.ipv4.conf.all.send_redirects = 0
#
# Do not accept IP source route packets (we are not a router)
#net.ipv4.conf.all.accept_source_route = 0
#net.ipv6.conf.all.accept_source_route = 0
#
# Log Martian Packets
#net.ipv4.conf.all.log_martians = 1
#




这几行都没有，没找到，要自己添加吗？

option

别折腾了，啥用没有，刚弄完，发现gg 还是要验证，解琐也不行。